How do I trace a photo onto wood?
Choose the photo you want on your wood (JPG, PNG, WebP or iPhone HEIC).


The easiest way to learn how to trace onto wood is to print your design at full size, tape it to the board and draw over the lines with graphite paper underneath. Choose a photo here and the page splits it over as many sheets as the poster needs. You see how many sheets there are and how wide the poster comes out, then print the PDF and tape the sheets together. The photo stays on your device, and a PDF of up to 2 by 2 sheets is free.
Knowing how to trace onto wood comes down to three things: a pattern the size of the board, tape to hold it still, and a layer that leaves a line, such as graphite paper. Print the pattern here, tape it down and press along the lines with a pencil or ballpoint pen. With no transfer paper, shade the back of the pattern with a soft pencil and trace over the front.
How to use how to trace onto wood
Choose your photo
Press “Choose a photo” and pick the picture you want on the wood. On a computer you can also drag it onto the page. The poster choices are already open.
Match the poster to your board
Set “Sheets across” or type a “Poster width” in inches or cm. The line below says how many sheets you need, how wide the poster prints and about how many pixels per inch the photo gives.
Save the PDF and print it
Tick “Print grid lines on the poster” only if you want squares on the pattern. Press “Save free poster PDF”, then print the PDF at 100% or actual size.
Tape the sheets and trace
Each sheet has a white edge and no alignment marks, so trim the white edge on the joining side of the sheet that lies on top, then lay it over the 6 mm strip of the same picture on the next sheet and line the picture up. Tape the seams on the back, then tape the pattern to the wood. Slide graphite paper under it and trace the outlines.
Choose a design that traces well
Pick a picture with clear outlines, such as a plant, an animal, a lettered shape or a building. A busy photo full of small shadows gives you a tangle of lines, and it is hard to tell which ones matter. If your photo is busy, turn it into a pencil sketch or a black and white stencil on the photo to sketch or photo to stencil page, save the PNG and choose that picture here instead.
Size the poster to your board
Measure the wood before you set anything. Type the width you want the design to cover into “Poster width” and leave a margin of bare wood around the edge so the finished piece does not look cramped. Then read the line under the field. For tracing, a soft photo is fine, because you follow outlines rather than fine detail. If the number is under 100 pixels per inch, the edges look soft up close, and a smaller width will give crisper lines.
When you print, choose 100% or actual size in the print window. “Fit to page” shrinks every sheet, and the poster comes out smaller than the width you typed.
Tape the sheets together from the back
Lay the printed sheets face up in order. Each sheet has a white edge and no alignment marks, so trim the white edge on the joining side of the sheet that lies on top, then lay it over the 6 mm strip of the same picture on the next sheet and line the picture up until it runs straight across with no step, then tape the seam on the back. Taping on the back keeps the front smooth, so graphite paper and your hand glide over it. Painter’s tape peels off paper and wood easily.
If you ticked “Print grid lines on the poster”, the lines show at a glance whether the pattern has drifted while you taped, and they give you straight edges to square against the edges of the board.
Place the pattern on the board
Before you tape anything down, find the center of the board by measuring its width and height and marking the halfway points with a light pencil tick. Fold the finished pattern in half both ways to find its own center, then line the two up. A design that sits a little high looks better than one that sits dead center, so nudge it up slightly if the board has a visible top and bottom.
Check that a straight edge of the pattern runs parallel to the edge of the board. Wood grain makes a crooked design easy to notice, especially on long planks, so measure from the pattern to the board edge at both ends before you commit.
Prepare the wood
Sand the board with fine sandpaper until it feels smooth, then wipe off the dust with a dry cloth. Dust under the pattern makes the transfer paper slip, and rough grain makes the pencil jump off the line. Work on bare wood, and keep your hands clean so skin oils do not mark the surface.
If you have a scrap of the same wood, try your pencil or pen on it first. A few test lines show how much pressure leaves a clear mark and how much starts to dent the surface.
Match the transfer method to the wood
Graphite paper on light wood
Place the graphite paper dark side down on the wood, lay the pattern on top and trace. It is cheap, leaves a thin gray line and can be used again for the next project. It suits detailed designs and is the usual choice for pale wood.
White graphite or chalk paper on dark wood
Regular graphite disappears on walnut or stained boards. White graphite or chalk transfer paper leaves a pale line you can see. Chalk lines rub away with a fingertip, which makes mistakes easy to fix but means you should not slide your hand across the board while you work.
Pencil on the back when you have no transfer paper
Turn the pattern over and shade behind the lines with a soft pencil, covering a little beyond the edge of each line. Turn it face up, tape it down and trace. The graphite on the back prints onto the wood wherever you press. Thin paper gives the sharpest result, and each pass can be re-traced if the line looks faint.
Hold the pattern still and trace with care
Start by taping only the top edge, so the pattern hinges like a page. Slip the graphite paper under, trace a few lines, and lift the corner to check the result before you tape the other sides. Once the pattern is fixed in place, keep it there until every line is traced, because it is almost impossible to put it back in exactly the same spot.
Press with light to medium pressure. Heavy pressure dents soft wood such as pine and pushes extra graphite into the grain, which smudges. A ballpoint pen is handy because its ink marks the paper as you go, so you can see which lines are done. Trace the outer shape first, then the inner details.
Work in a sensible order on a big design
On a poster-size pattern, trace one sheet at a time and start at the top so your hand never rests on lines you have already made. Rest your wrist on a clean scrap of paper if you have to lean across the board. Where a line crosses a taped seam, press a little more slowly, because the tape adds a small ridge under the paper.
Clean up the lines
When the tracing is finished, go over the lines with whatever comes next, whether that is paint, a marker or a wood burner. Burn or paint right along the traced line so little needs removing afterwards. Any graphite left over can be erased lightly or sanded away with fine sandpaper along the grain. If you are burning, work on a heat-safe surface in a ventilated room.
FAQ
How do I trace something onto a piece of wood?
Print the design at the size you want, tape it to the wood and slide graphite paper, dark side down, between the two. Trace the lines with a pencil or ballpoint pen using light to medium pressure. Lift one corner now and then to check that the lines have transferred before you remove the pattern.
How do I trace onto wood without tracing paper?
Shade the back of the pattern with a soft pencil, then tape it face up and trace the lines. The pressure pushes graphite from the back onto the wood, so no transfer sheet is needed. Thin printer paper works best, because thick paper needs firmer pressure, which can dent soft wood.
What should I use to trace onto dark wood?
Use white graphite paper or chalk transfer paper instead of regular graphite paper. Both leave a pale line that shows on dark wood. Chalk lines rub off easily, so start your drawing, painting or burning soon after tracing and avoid handling the board more than you need to.
Can I trace a design that is bigger than one sheet of paper?
Yes. Set “Sheets across” or type your poster width, and the page splits the photo over as many sheets as it needs. Neighboring sheets share a 6 mm strip of the same picture: trim the white edge off the top sheet, line the picture up and tape it. The free PDF covers up to 2 by 2 sheets.
How do I remove traced lines from wood?
Erase graphite gently with a soft eraser, or sand lightly along the grain with fine sandpaper. A slightly damp cloth lifts chalk lines. Test a hidden spot first, because rubbing hard can push graphite into the grain and leave a smudge.
Updated
Related tools
- 10x10 gridPrint a blank 10x10 grid with 100 squares in three sizes. Add numbers 1 to 100, then print the sheet or save it as a clear PNG.
4 Quadrant Graph PaperPrint free 4 quadrant graph paper with bold x and y axes, numbered both ways from 0. Pick square size and paper, then save as PDF, PNG or JPG.- 8x8 gridPrint a free 8x8 grid of 64 squares in your browser. Pick Small, Medium or Large squares, add letters and numbers, then print or save a PNG.
Add grid to photoAdd a grid to any photo in your browser, with no sign-up and no watermark. Get a numbered grid or a plain grid overlay, then save it or print it at true size.- Ar TracingInstead of ar tracing with a phone stand, put a numbered grid on your own photo, then save or print it and copy it square by square. Free, no sign-up.
Aspect Ratio CalculatorUse this aspect ratio calculator to turn a width and height into a ratio like 16:9. You also get the decimal and a resize that keeps the shape.- Atmospheric PerspectiveAdd a numbered grid to a photo and compare near and far squares to see atmospheric perspective: lighter values, softer color. Free, in your browser.
- Bargue DrawingPractice Bargue drawing from your own photo: add a numbered grid with 5, 8 or 12 squares across, then save it or print a gridded sheet and an empty one.